Installing Your Windows (Professional Wood Window Removal)
I. REMOVAL OF EXISTING WOOD WINDOW
Check new windows before you tear out opening. Make sure you have the correct amounts and sizes.
Carefully remove exterior blind stops.
Cut bottom sash balance cord or chain and remove sash, or take out sash balances.
Remove the parting strips at the sides and top(s).
Cut top sash balance cord or chain and remove the sash.
II. PREPARATION OF OPENING AND INSTALLATION PROCESS
Clean opening thoroughly and verify integrity of existing wood (replace damaged or rotten components as necessary).
Apply head expander (if needed) to window using loose fiberglass insulation to fill cavity.
Apply foam insulation to window on sides and top (do not use expandable foam as it puts too much pressure on window).
Set locked window into opening.
Replace blind stops against window on outside. Adjust window to opening, as all openings, especially on older homes, are not level or plumb. The window may be installed a little out of square or level to adjust for appearance of finished product. Make sure that margins on weatherstripping are tight enough to make a proper seal.
Unlock and raise bottom sash and bottom sash stops. Install screws into pre-drilled installation holes. DO NOT over-tighten screws. Tighten only when window is completely set.
If installing a double hung window, lower the top sash and top sash stops. Install screws into pre-drilled installation holes. DO NOT over-tighten screws.
Check window frame for correct weatherstripping margins and adjust installation screws as necessary.
The jamb adjustment grommet screws are located in both side jambs of the window. With a flat head screwdriver, turning the screws in a clockwise direction will cause the jamb to "pull" toward the center of the window. This adjustment is necessary to give a closer and more even alignment between the sash and frame. The distance between the operating sashes and the jambs of the window should not exceed 3/32. After making practical adjustments, replace the sashes, operate them and visually judge their alignments with the jambs. (On 8000 Series windows shims may be needed. However, the foam insulation usually takes care of this.) Adjustments may have to be made several times until satisfactory performance is achieved. You may also make adjustments by loosening and tightening the previously installed jamb screws.
In extreme cases the old window opening might be badly "bowed". If the adjustments do not solve this problem, wood shims will have to be used between the rough opening and the replacement window jambs.
If the top head expander is used, adjust it up against the rough opening.
Caulk around the entire perimeter of the window on the inside with paintable sealant.
Replace the old window trim stops or install new strips around the inside of the window at the head and jambs.
Professional capping should be performed in a way that does not allow penetration around the vinyl window. Pressure bends to window and sealant (in corners and bottom areas where vertical members meet sill) should be expected.
WARRANTY: One warranty registration should be submitted for each window job. Ask your dealer for the appropriate registration form.
All old windows’ debris is completely cleaned up and hauled away at no additional charge.
Most installations are completed in one day.
Installing Your Windows (DIY Wood Window Removal)
I. REMOVAL OF EXISTING WOOD WINDOW
Check new windows before you tear out opening. Make sure you have the correct amounts and sizes.
Carefully remove all inside trims or stops (you will reuse this material).
Cut bottom sash balance cord or chain and remove sash.
Remove the parting strips at the sides and top(s).
Cut top sash balance cord or chain and remove the sash.
Leave exterior stops (blind stops) intact and in place to prevent replacement window falling through opening.
II. PREPARATION OF OPENING AND INSTALLATION PROCESS
Clean opening thoroughly and verify integrity of existing wood (replace damaged or rotten components as necessary).
Apply a discontinuous bead of sealant to the bottom of the sill angle at two locations (this allows water to "weep" away from the window) and place on sill.
Apply a bead of sealant to the interior of the exterior stop and to the exterior edge of the stool.
Apply head expander (if needed) to window using loose fiberglass insulation to fill cavity.
Set locked window into opening and against wet sealant.
Apply a bead of sealant to interior face of window.
Replace interior stops (blind stops) against wet sealant.
Unlock and raise bottom sash and bottom sash stops. Install screws into pre-drilled installation holes. DO NOT over-tighten screws.
If installing a double hung window, lower the top sash and top sash stops. Install screws into pre-drilled installation holes. NO NOT over-tighten screws.
Check window frame for square (measure diagonals) and adjust installation screws as necessary.
The jamb adjustment grommet screws are located in both side jambs of the window. With a Phillips head screwdriver, turning the screws in a clockwise direction will cause the jamb to "pull" toward the center of the window. This adjustment is necessary to give a closer and even alignment between the operation. The distance between the operating sashes and the jambs of the window should not exceed 1/16". After making practical adjustment, replace the sashes, operate them and visually judge their alignments with the jambs.
Adjustments may have to be made several times until satisfactory performance is achieved. You may also make adjustments by loosening and tightening the previously installed jamb screws.
In extreme cases the old window opening might be badly "bowed." If the adjustments do not solve this problem, wood shims will have to be used between the rough opening and the replacement window jambs.
If the top head expander is used, adjust it up against the rough opening.
Caulk around the entire perimeter of the window on the inside with paint able sealant.
Replace the old window trim stops or install new strips around the inside of the window at the head and jambs.
WARRANTY: One warranty registration should be submitted for each window job. Ask your dealer for the appropriate registration form.
All old windows debris is completely cleaned up and hauled away at no additional charge.
Most installations are completed in one day.
